Cost estimator

Well Pump Replacement Cost Calculator

Pump type and well depth drive most of the price. Enter what you know and get a realistic installed range, what each extra adds, and the cheaper fixes to rule out before you replace the pump.

  • You needWell depth if you know it
  • Takes1 minute
  • CostFree, no sign-up

Short answer: replacing a well pump costs about $1,000 to $2,800 for most homes, and Angi’s national average is $1,897. A deep well, a constant pressure system or a new pressure tank can push the bill past $4,000. A small repair might fix the problem for a few hundred dollars instead.

$1,897national average to replaceAngi, 1,339 projects
$974average pump repairAngi
3–6 hrsfor a typical swapHomeGuide
8–15 yrsnormal pump lifeHomeGuide

The calculator above gives you a range for your own well. This guide covers everything around that number: what’s in a fair quote, which repairs to rule out first, when a new pressure tank makes sense, and how to tell a good price from a padded one.

How much does it cost to replace a well pump?

Angi looked at 1,339 real pump replacements and found most homeowners paid between $974 and $2,821. The average was $1,897.

That covers most jobs, but not all of them. Three things push a job past the top of that range:

  • A deep well, where the crew has to pull and reset hundreds of feet of pipe and wire
  • Upgrading to a constant pressure system
  • Replacing the pressure tank, switch or wiring at the same time

On the other end, a shallow well with a jet pump in the basement can come in well under $1,000.

Well pump replacement cost by city

Where you live changes the price more than most people expect. Here’s what Angi reports in a few metro areas:

AreaAverageTypical range
Tampa, FL$3,609$1,560 to $5,658
Austin, TX$2,937$1,936 to $4,310
Denver, CO$2,102$1,065 to $3,139
New York, NY$2,051$1,290 to $2,832
Chicago, IL$1,285$845 to $2,165
National$1,897$974 to $2,821

Source: Angi city cost pages, updated July 2026; national figure updated August 2026.

Typical range by cityBar shows the range, dot shows the average. Angi.
Tampa, FL$3,609 avg
Austin, TX$2,937 avg
Denver, CO$2,102 avg
New York, NY$2,051 avg
Chicago, IL$1,285 avg
National$1,897 avg
$0$1.4k$2.8k$4.2k$5.7k

Local labor rates explain part of the gap. Typical well depth explains the rest: in areas where wells run deep, every replacement means pulling more pipe.

Before you pay for a new pump: a tripped breaker, a burned pressure switch or a waterlogged tank can look exactly like a dead pump. Those fixes cost a fraction of a replacement. See what your symptoms mean below.

How to use the well pump replacement cost calculator

You can get a result with no inputs at all. Each answer you add makes it closer to your real job.

QuestionWhy it mattersWhere to find it
Pump typeA shallow jet pump and a deep submersible are very different jobs.If nothing sits next to the tank, the pump is down in the well.
Well depthThe biggest driver. More depth means more pipe, more wire and a longer pull.Your well log, or a tag on the well cap.
What’s happeningShows the cheaper fixes to check before replacing anything.What you notice at the tap.
New pressure tankAdds the installed price for the size you pick.The size is printed on the tank label.
Constant pressurePrices the job as a constant pressure system instead of a standard pump.Only tick it if you want steady pressure.
Emergency callAdds Angi’s $150 to $300 after-hours fee.Tick it if you can’t wait for a weekday.

Don’t know your depth? Our well record finder shows where your state keeps well logs. The log also tells the contractor what pump size and how much pipe to bring, which saves a second trip.

Well pump replacement cost by pump type

Your pump type is mostly decided by how deep the water is. You usually replace like with like.

Pump typeInstalled costWhere it’s used
Shallow well jet pump$400 to $1,500Water close to the surface. The pump sits above ground.
Deep well jet pump$500 to $2,200+Deeper water, pump still above ground
Submersible pump$1,000 to $2,500+Most drilled wells. The pump sits down in the water.
Constant pressure pump$1,300 to $5,000Steady pressure when several taps run
Solar pump$1,500 to $6,500+Off-grid homes, cabins, livestock
Hand pump$200 to $2,000Backup water during power outages

Ranges cover both HomeGuide (August 2025) and Angi (August 2026).

Installed cost by pump typeLowest to highest published price, HomeGuide and Angi
Hand$200–$2k
Shallow jet$400–$1.5k
Deep jet$500–$2.2k
Submersible$1k–$2.5k
Constant pressure$1.3k–$5k
Solar$1.5k–$6.5k
$0$1.6k$3.3k$4.9k$6.5k

Which type do you have?

Go to the pressure tank, usually in the basement, garage or a utility room. If a pump with a motor sits right next to it, you have a jet pump. If there’s only the tank, a pressure switch and maybe a gray control box on the wall, your pump is a submersible down in the well.

Can you switch types? Sometimes. When a shallow jet pump keeps losing its prime, a contractor may suggest a submersible if the well casing is wide enough. Ask before you agree, since it changes the price.

Jet pump vs. submersible

Side-by-side cutaway of a jet pump in a basement drawing from a shallow well, and a submersible pump hanging deep in a drilled well
Where each pump sits: above ground beside the tank, or down in the well below the water line.
Jet pumpSubmersible pump
Where it sitsAbove ground, near the tankDown in the well, under water
Best forShallow waterDeep drilled wells
Replacement costLower, no pulling from the wellHigher, the crew pulls pipe and wire
NoiseYou can hear it runQuiet, it’s underground
Common troubleLosing prime, leaks at fittingsMotor or wiring failure down the hole
ServiceEasy to reachNeeds a pump hoist to reach

Less common pumps and what they cost

PumpInstalled costWhen it makes sense
Booster pump$1,000 to $2,000+Adds pressure after the tank, for example in a home on a hill
Solar pump$1,500 to $6,500+No power line at the well, cabins, stock tanks
Hand pump$200 to $2,000A backup for power outages
Windmill pump$4,000 to $21,500+Remote livestock water

HomeGuide and Angi ranges.

A hand pump is worth a thought if you lose power often. Some models can be installed in the same well as your electric pump, so you still have water when the lights go out. Ask a contractor whether your casing has room for both.

Well pump replacement cost by depth

Depth matters more than the pump. A submersible pump can cost about the same at 100 feet or 400 feet. What changes is everything around it: the length of pipe and wire, how big the motor has to be to push water up, and how long the crew spends pulling the old pump out.

Well depthReplacement costUsual pump
Under 25 ft$400 to $3,000+Shallow well jet pump
25 to 150 ft$1,200 to $5,500+Deep well jet or submersible
Over 150 ft$2,000 to $10,000+Submersible

Source: Angi, updated August 2026.

Replacement cost by well depthAngi national ranges
Under 25 ft$400–$3k+
25–150 ft$1.2k–$5.5k+
Over 150 ft$2k–$10k+
$0$2.5k$5k$7.5k$10k

Want to know how deep wells usually go where you live? Our water well drilling cost calculator shows typical depths by county for the states where we have well records.

How a well pump system works

It helps to know the parts before you read a quote. Water takes this path from the well to your tap:

  1. The pump pushes water upA submersible sits below the water line inside the casing. A jet pump sits above ground and pulls water up instead.
  2. The drop pipe carries it to the surfaceThe pump hangs on this pipe, along with its power wire.
  3. The pitless adapter turns it toward the houseBelow the frost line, the water leaves the casing through a buried line.
  4. The pressure tank stores some under pressureSo the pump doesn’t have to start every time you open a tap.
  5. The pressure switch runs the showWhen tank pressure drops to the low setting, it starts the pump. At the high setting, it shuts it off.
Basement well water system with a blue pressure tank, pressure switch and gauge on the tank tee, and a gray control box on the wall
A typical setup for a submersible pump: the tank, the switch and gauge on the pipe below it, and the control box on the wall.

That’s why a “no water” call can come from any of these parts. The pump is just the most expensive one.

What’s included in the price

A pump replacement is more than the pump. Here’s what a full job usually covers, and what to check for on your quote.

Part of the jobWhat it isAlways replaced?
The pumpThe motor and pump unit itselfYes
Drop pipeThe pipe that carries water from the pump to the top of the wellOften, if it’s old or damaged
Pump wireThe power cable that runs down to the pumpOften, especially if it’s spliced or brittle
Control boxWall box that starts the motor on 3-wire pumpsOnly if it’s failed or doesn’t match the new pump
Pressure switchTells the pump when to turn on and offCheap, so often swapped while the crew is there
Check valveStops water draining back down the wellSometimes
LaborPulling the old pump, setting the new one, testingYes

What labor costs

Labor itemCostSource
Plumbing labor for a pump job$250 to $1,000HomeGuide $250–$800; Angi $250–$1,000
Pump technician hourly rate$45 to $150 per hourAngi
Electrician hourly rate$50 to $130 per hourHomeGuide $50–$130; Angi $50–$100
House call fee$100 to $150Angi

The one question to ask every contractor: “Are you replacing the pipe and wire, or reusing them?” Reusing old pipe and wire lowers the quote. But if either fails in a year or two, the crew has to pull the whole thing again, and you pay that labor twice.

Repair or replace the pump?

Plenty of “dead pump” calls turn out to be something cheaper. Angi says the average well pump repair costs $974, and most fall between $373 and $1,624. Small parts cost far less than that.

RepairTypical costSource
Pressure switch$120 to $175 installedAngi
Motor start capacitor$100 to $150Angi
Pressure gauge$100 to $175Angi
Control box$200 to $500Angi
Pressure tank bladder (part)$50 to $100HomeGuide
Shallow jet pump repair$200 to $500Angi
Deep jet pump repair$400 to $800Angi
Pump motor$500 to $1,000HomeGuide
New pressure tank, installed$800 to $1,500HomeGuide
Repair costs next to a full replacementAngi and HomeGuide ranges
Capacitor$100–$150
Pressure switch$120–$175
Control box$200–$500
Pump motor$500–$1k
Pressure tank$800–$1.5k
New pump$974–$2.8k
$0$700$1.4k$2.1k$2.8k

Repairs vary by area too. Angi found the average repair in Washington state ran about $1,710, while in Miami it was roughly $400.

A simple way to decide

Lean toward repair

  • The pump is less than about 8 years old
  • The problem is above ground: switch, tank, gauge or control box
  • Water was fine until it suddenly stopped
  • The repair costs well under half of a new pump

Lean toward replacing

  • The pump is past its 8 to 15 years
  • The motor itself has failed
  • Pressure has been getting weaker for months
  • Your power bill crept up with no other reason
  • The crew is already pulling the pump for another repair

That last point matters. Pulling a submersible is a big part of the labor. If the pump is old and has to come up anyway, putting a new one in while it’s out often costs less than paying for two trips.

What your symptoms usually mean

Start at the top of this list. The first checks are free.

  1. Check the breakerA tripped breaker or blown fuse is the cheapest fix there is. If it trips again right away, stop and call a pro.
  2. Look at the pressure gaugeNo pressure with the pump off points to the pump or its power. Pressure that bounces up and down points to the tank or switch.
  3. Listen at the tankIf the pump clicks on and off every few seconds while a tap runs, the tank has likely lost its air.
  4. Check the filterA clogged sediment filter can make pressure drop slowly over weeks.
  5. Call a licensed pump contractorIf none of that explains it, the problem is likely down the well.
What you noticeCommon causeBallpark cost
No water at allBreaker, pressure switch, capacitor or the pump itself$0 to $175 for small parts; a new pump if the motor is gone
Pump clicks on and off fastWaterlogged pressure tank or failing switch$120 to $175 for a switch, $800 to $1,500 for a tank
Weak pressureClogged filter, switch setting, worn pumpA filter cartridge up to a new pump
Pump never shuts offA leak, a bad check valve or a worn pumpVaries; find the leak first
Sputtering taps or airWater level dropping near the pump, or a leak in the drop pipeNeeds a contractor to check
Sand or mud in the waterPump set too low, or a worn well screenNeeds a contractor to check
Higher power billA worn pump running longer to keep upOften a sign replacement is coming

Repair costs from Angi and HomeGuide. Water problems like sand, smell or color? Try our well water symptom checker.

Low pressure that isn’t the pump’s fault

The National Ground Water Association’s well owner site points to two causes people often miss:

  • The pump is too small for the house. If your home needs 10 gallons a minute and the pump gives 5, you get a trickle. This often shows up after adding a bathroom.
  • Scale in the pipes. Hard water leaves deposits that narrow the pipes and cut pressure, even with a healthy pump.

In both cases, a new pump of the same size won’t fix it. Tell the contractor if you’ve added fixtures or have hard water, so they size the fix correctly.

Early warning signs

Pumps rarely die without a few hints first. HomeGuide and Angi both list the same early signs. Catching them early lets you replace the pump on a weekday, at normal rates, instead of in a Sunday-night emergency.

SignWhat it can meanHow soon to act
Pressure slowly getting weakerA worn pump, or a clogged filterWithin weeks
Faucets spitting airWater level near the pump, or a leak in the drop pipeSoon, running dry damages the motor
Cloudy or sandy waterThe pump is stirring up sedimentSoon
Odd noises at the tank or pumpWorn bearings, or rapid cyclingWithin weeks
Power bill creeping upThe pump runs longer to do the same workPlan a replacement
Pump running all the timeA leak, or a pump that can’t reach cut-off pressureNow
Bad smell in the waterBacteria or a water quality changeTest the water now
Safety first: well pumps run on 240 volts. Turn the power off at the breaker before you touch a pressure switch, and leave anything inside the control box or down the well to a licensed contractor.

Should you replace the pressure tank too?

Pumps and tanks wear out on a similar schedule. HomeGuide puts both at roughly 10 to 15 years. And a failing tank can kill a new pump early by making it start and stop far too often.

So if your tank is about as old as your pump, it’s worth replacing them together while the crew is already there.

Tank sizeTank onlyInstalled
20 to 29 gallons$200 to $500$450 to $1,000
30 to 39 gallons$300 to $850$550 to $1,350
40 to 59 gallons$350 to $1,100$600 to $1,600
60 to 79 gallons$500 to $1,300$750 to $1,800
80 to 99 gallons$600 to $1,800$850 to $2,300
100 to 119 gallons$850 to $2,000$1,100 to $2,500

Source: HomeGuide, July 2025. Labor alone runs $250 to $500+.

Signs the tank is the problem

  • The pump turns on and off every few seconds while water runs
  • Pressure swings up and down at the tap
  • The whole tank sounds solid when you tap it, instead of hollow near the top
  • Rust or water around the base

Picking the right size pump

A pump that’s too small leaves you with a trickle when two people shower. One that’s too big costs more and can pull the well down faster than it refills. The Water Systems Council gives two simple ways to size it.

Quick rule: the pump should supply about one gallon per minute for every water fixture in the house.

Peak demand method: size for the busiest few minutes of the morning.

BathroomsWater used in peak 7 minutesPump size needed
145 gallons7 gpm
2 to 2.598 gallons14 gpm
3 to 4122 gallons17 gpm

Source: Water Systems Council, “Sizing a Well Pump.”

There’s one limit no pump can get around: the well itself. If the well only gives 5 gallons a minute, a 14 gpm pump won’t change that. The well log shows the yield measured when it was drilled.

Pressure settings matter too. The Water Systems Council says most home systems run between 30 and 50 psi or between 40 and 60 psi.

Is a constant pressure system worth it?

A standard pump runs at one speed and switches on and off as the tank pressure rises and falls. A constant pressure (variable speed) pump speeds up and slows down to match how much water you’re using, so pressure stays steady.

Standard pumpConstant pressure
Installed cost$1,000 to $2,500+ (submersible)$1,300 to $5,000
Pressure at the tapRises and falls between switch settingsSteady
Tank neededLarger tankSmaller tank
Best forMost homesLarger homes, many bathrooms, irrigation

Costs: HomeGuide and Angi.

The National Ground Water Association’s well owner site also points to a cheaper middle option: a constant pressure valve added to a standard pump. It calls it a “good, economic solution” for uneven pressure.

Our take: if your pressure was fine before the pump died, a standard replacement is the sensible choice. A constant pressure system is an upgrade, not a repair.

Three example jobs

These are run through the calculator above, so you can see how the pieces add up.

Simple swap

Shallow jet pump, 20 ft

  • Pump in the basement
  • Keep the existing tank
  • Weekday visit
Wells under 25 ft
$400 to $3,000+
Total
$400 to $3,000+

The jet pump itself runs $400 to $1,500 installed. Extra repairs push it toward the top.

Most common

Submersible, 180 ft

  • Replace the pump
  • New 40-gallon tank
  • Weekday visit
Wells over 150 ft
$2,000 to $10,000+
Tank, installed
$600 to $1,600
Total
$2,600 to $11,600+

A submersible alone is $1,000 to $2,500+. Pipe, wire and labor at this depth decide the rest.

Upgrade

Constant pressure, 120 ft

  • Switch to a variable speed system
  • Saturday emergency call
System, installed
$1,300 to $5,500+
After-hours fee
$150 to $300
Total
$1,450 to $5,800+

In a well over 150 ft, the top end climbs toward $10,000.

Emergency calls and how long it takes

No water is stressful, and contractors know it. Angi says after-hours service adds $150 to $300, on top of a typical $100 to $150 house call fee.

When you callWhat to expect
Weekday, business hoursStandard rates
Evening, weekend or holiday$150 to $300 extra (Angi)
The job itselfAbout 3 to 6 hours for most replacements (HomeGuide)

If you can get by for a day or two, it’s often worth waiting for a weekday. Fill some jugs, ask a neighbor, and use the time to get a second quote.

Well service crew using a truck-mounted pump hoist to pull a submersible pump and drop pipe out of a residential well
Pulling a submersible: the pump comes up on its drop pipe and wire, lifted by a hoist truck.

What happens on replacement day

  1. Power off and diagnosisThe tech confirms the pump is the problem, not the switch or the tank.
  2. Pulling the pumpFor a submersible, the crew lifts the pump, pipe and wire out of the well, often with a pump hoist truck.
  3. InspectionThey check the pipe, wire and fittings to see what can be reused.
  4. New pump setThe new pump goes in at the right depth, with new pipe and wire if needed.
  5. TestingPressure settings are checked and the system runs through several cycles.
  6. DisinfectionMany contractors chlorinate the well after it’s been opened. Ask if yours does.

Can you replace a well pump yourself?

A shallow jet pump swap is within reach for a handy homeowner. A submersible is a different story.

  • You’re working with 240-volt power and water at the same time.
  • A deep pump with water-filled pipe can weigh hundreds of pounds.
  • Dropping the pump down the well turns a repair into a much bigger bill.
  • Opening the well can let bacteria in if it isn’t disinfected after.
  • Angi notes that DIY repair can void the manufacturer’s warranty.

The National Ground Water Association puts it plainly: installing valves, tanks and pumps “is not for amateurs.”

Before the contractor arrives

A few minutes of prep can shorten the visit and make the quote more accurate.

Do thisWhy it helps
Find your well logShows depth, pump setting and yield, so they bring the right parts
Read the tank labelSize and date tell them if the tank should be replaced too
Note what happened and whenSudden failure and slow decline point to different problems
Take a photo of the gauge, switch and control boxHelps with phone quotes
Clear a path to the wellheadA pump truck needs to get close to the well
Find old receiptsThe old pump may still be under warranty

Getting by without water

  • Keep a few gallons of bottled water for drinking and cooking.
  • Fill buckets from a neighbor’s outdoor tap to flush toilets.
  • Turn off the power to your water heater if it’s electric, so it doesn’t heat an empty tank.
  • Once water is back, run the cold taps until the water runs clear.

How to compare well pump quotes

Ask for itemized quotes and line them up. Most price gaps come from what’s included, not from the pump.

CheckQuote AQuote BQuote C
Pump brand, model and horsepower
Flow rating (gpm) at your depth
New drop pipe? Type and length
New wire? Length
Pressure switch, check valve included?
Pressure tank included? Size
Disinfection after the job?
Warranty on parts and labor
After-hours fee
License number checked

Questions worth asking every contractor:

  • Have you confirmed it’s the pump and not the switch, tank or wiring?
  • Are you replacing the pipe and wire, or reusing them?
  • What size pump are you putting in, and why that size?
  • How old is my pressure tank, and does it need replacing too?
  • What warranty comes with the pump and with your labor?
  • Will you disinfect the well before you leave?
  • Are you licensed for pump installation in this state?

What a clear quote looks like

Here’s the shape of a well-written quote for a typical submersible job. The prices are the published ranges from this page, so you can see where each line should land.

Line itemWhat it should sayPublished range
Service callTrip and diagnosis$100 to $150
Pump, installedBrand, model, horsepower, gpm rating$1,000 to $2,500+
Pipe and wireNew or reused, type and lengthShould be listed, not hidden
Pressure switchNew or reused, pressure settings$120 to $175
Pressure tank (if needed)Size in gallons$450 to $2,500 by size
DisinfectionChlorinate the well after the jobAsk if included
WarrantyParts and labor, in writingAsk for the terms

If a quote can’t fill in most of these lines, ask for a revised one before you agree to anything.

Red flags

  • A replacement quote before anyone has checked the switch or tank
  • One lump sum with no brand, horsepower or parts list
  • Pushing a constant pressure upgrade when your old system worked fine
  • No license number, or one you can’t find in state records
Need a pump contractor?

Find licensed well and pump contractors in your county, with license details from state records.

Find a licensed contractor

Common mistakes that cost well owners money

MistakeWhat it costs youDo this instead
Replacing the pump without checking the switch and tankA $1,000+ job for a $150 problemAsk for a diagnosis first
Keeping a dying tank with a new pumpA shorter life for the new pumpCheck the tank’s age and air charge
Reusing 20-year-old pipe and wire to save moneyA second pull, and paying labor twiceAsk what condition they’re in
Buying a bigger pump than the well can supplyRunning the well dry and burning out the motorSize the pump to the well’s yield
Calling on a Saturday when it could wait$150 to $300 in after-hours feesGet by for a day if you safely can
Skipping the water test afterwardDrinking water that may carry bacteriaDisinfect and test at a certified lab
Taking the only quote you gotOverpaying, or missing a cheaper repairGet two or three itemized quotes

Making the new pump last

PartTypical lifeSource
Well pump8 to 15 yearsHomeGuide
Pressure tank10 to 15 yearsHomeGuide
The well itself30 to 50 yearsHomeGuide

Where your pump lands in that range depends a lot on how it’s treated. The habits that help most:

  • Keep the tank healthy. A waterlogged tank makes the pump start and stop over and over, which wears out the motor.
  • Don’t let it run dry. If taps sputter during heavy use, the pump may be drawing the water down too far. Spread out laundry, showers and watering.
  • Protect it from power surges. Ask an electrician about surge protection if you get a lot of lightning.
  • Deal with sediment. Sand wears pump parts. If you see grit, have the setting depth and screen checked.
  • Test the water yearly. The CDC suggests a yearly check for bacteria, nitrate, total dissolved solids and pH. Opening the well for pump work is another good reason to test. Find a certified lab near you.

Does homeowners insurance cover a well pump?

Usually not for normal wear. A pump that simply wore out after 12 years is a maintenance cost under most policies. Sudden damage is different: a lightning strike or a fire may be covered. Call your insurer before the work starts and keep the old pump and the contractor’s notes in case you need to file a claim.

Planning ahead: what to budget

Well owners don’t get a water bill, but the system still costs money over time. Spreading the big replacements across their expected life gives you a rough yearly number to set aside.

ItemCostHow oftenPer year, roughly
Pump replacement$1,897 averageEvery 8 to 15 years$125 to $240
Pressure tank$800 to $1,500Every 10 to 15 years$55 to $150
Water testVaries by labEvery year (CDC)Check our lab finder for fees

Costs from Angi and HomeGuide; yearly figures are simple division, rounded.

Putting a couple hundred dollars a year aside means a dead pump is an annoyance, not an emergency loan.

Buying a home with a well?

The pump is easy to overlook during a home purchase, and it’s one of the first big bills new owners face. Before closing, ask the seller:

  • How old is the pump, and when was the pressure tank replaced?
  • Who services the well, and are there any receipts?
  • Is there a well log? Our well record finder shows where your state keeps them.
  • When was the water last tested, and by which lab?

If the pump is near the end of its 8 to 15 years, use this page’s numbers to ask for a credit or plan the cost into your first year.

Cold weather and jet pumps

A jet pump and the pipe to it sit above ground, so they can freeze in an unheated well house, crawl space or garage. A frozen pump can crack its housing, which turns into a replacement. If your pump lives somewhere cold, insulate the space or add a small heat source made for the job, and keep the door shut in winter. Submersible pumps sit below the frost line and don’t have this problem.

Warranties

Pumps usually come with a manufacturer’s warranty, and many contractors add their own warranty on labor. They’re two different things. The manufacturer covers the pump. The contractor covers the installation. Get both in writing, and keep the receipt with the pump’s model number. If the new pump fails early, that paperwork is what gets it replaced for free. Angi also warns that doing the repair yourself can void the manufacturer’s warranty.

When the problem is the well, not the pump

Sometimes a new pump won’t help. If the water level in the well has dropped below where the pump can reach, if the casing has failed, or if the well keeps running out no matter what pump is in it, you may be looking at deepening the well or drilling a new one. A contractor can measure the water level to tell. If it comes to that, our water well drilling cost calculator shows what a new well costs.

Well pump terms in plain English

TermWhat it means
Cut-in / cut-out pressureThe pressures where the switch starts and stops the pump, such as 40 and 60 psi.
psiPounds per square inch, how water pressure is measured.
gpmGallons per minute, how much water the pump or well delivers.
Pump settingHow far down in the well the pump hangs.
Static water levelWhere the water sits in the well when nothing is pumping.
DrawdownHow far the water level drops while the pump runs.
PrimeWater a jet pump needs inside it to start pumping.
Foot valveA one-way valve at the bottom of a jet pump’s suction pipe that keeps its prime.
Check valveA one-way valve that stops water from draining back down the well.
Control boxA wall box that starts the motor on 3-wire submersible pumps.
CapacitorThe part that gives the motor its starting kick. A common, cheap failure.
Torque arrestorA rubber collar that keeps a submersible from twisting in the casing when it starts.
Pitless adapterThe fitting where the water line leaves the casing below the frost line.
Pump hoistThe truck-mounted rig used to pull a submersible out of the well.

Well pump replacement cost FAQ

How much does it cost to replace a well pump?

Most homeowners pay $974 to $2,821, and Angi’s national average is $1,897. Deep wells, constant pressure systems and a new tank can push it higher.

How much does a submersible well pump cost to replace?

About $1,000 to $2,500+ installed, according to HomeGuide and Angi. Wells over 150 feet can run $2,000 to $10,000+ once all the pipe, wire and labor are counted.

How much is a shallow well jet pump?

$400 to $1,500 installed. It’s usually the cheapest replacement because the pump sits above ground.

Does a deeper well need a bigger pump?

Usually. The pump has to push water up the full height to the house and still deliver enough flow. The contractor picks the horsepower from your depth and how much water your home uses.

What size pump does my house need?

The Water Systems Council suggests about one gallon per minute per fixture, or 7 gpm for one bathroom, 14 gpm for two to two and a half, and 17 gpm for three to four.

Why does well pump replacement cost more in some cities?

Labor rates and typical well depth. Angi reports averages from $1,285 in Chicago to $3,609 in Tampa.

Can a jet pump be replaced with a submersible?

Often, if the well casing is wide enough and the well is deep enough. It costs more up front, but it can solve a jet pump that keeps losing its prime.

How long does a well pump last?

About 8 to 15 years. A healthy pressure tank, steady water levels and clean water help it reach the high end.

How long does it take to replace a well pump?

HomeGuide says about 3 to 6 hours for most jobs. Very deep wells or extra repairs can take longer.

Should I replace the pressure tank at the same time?

If it’s close to the pump’s age, yes. Both last roughly 10 to 15 years, and a bad tank can shorten the new pump’s life. An installed tank runs about $800 to $1,500.

How do I know if it’s the pump or the pressure switch?

If the pump hums or runs but pressure stays low, the pump may be worn. If nothing happens at all, check the breaker and the switch first. A switch costs about $120 to $175 installed.

Why is my well pump replacement quote so high?

Usually depth, new pipe and wire, a new tank, or a constant pressure upgrade. Ask for an itemized quote and compare it with the ranges on this page.

Is it worth paying extra for a constant pressure pump?

Only if you want steadier pressure, have a large home, or run irrigation. For most homes, a standard pump does the job for less.

What’s the most expensive part of replacing a well pump?

In a shallow well, the pump itself. In a deep well, usually the labor and the pipe and wire, because the crew has to pull and reset everything over the full depth.

Do I need a permit to replace a well pump?

It depends on your state and county. Some require a licensed pump installer and a permit, others don’t. Ask your contractor, and check your state page for the agency in charge.

Is my water safe after a pump replacement?

Opening the well can let bacteria in. Ask the contractor to disinfect the well, then test for bacteria at a certified lab before drinking it again.

What if I wait to replace a failing pump?

A pump that’s running constantly or cycling fast can fail completely, usually at the worst time. Then you pay after-hours rates on top of the replacement.

Prices checked September 2026. Cost estimates are for planning only and are not a contractor quote.