Private well guide

Well Water in New York: Testing, Rules, Labs and Licensed Contractors

About 1,856,000 people in New York get their water from a private well, by the U.S. Geological Survey's estimate. Here is what the state requires, where to get it tested, and who is licensed to work on it.

493Licensed contractorschecked against state records
45Certified labsfrom the state certified list
56Counties covered
1,856,000People on private wells10% of residents (USGS, 2010)

The short version: About 1.9 million New Yorkers, 10% of residents, drink from a private well (USGS estimate, 2010). The state registers the people who drill and keeps the record of every well, but the testing is left almost entirely to the owner. There is no statewide test for a new well or a home sale, though some county health departments require a passing sample before a new well can be used.

New York at a glance
Permit to drill a home well Not from the state. Most county health departments require one, and the driller files a preliminary notice with DEC
Who can drill it A DEC-registered water well contractor
Water test for a new well No statewide rule. Some county health departments require a passing test
Water test when a home sells Not required statewide. A few counties and towns do, and some lenders ask for one
Biggest natural concern Depends on the rock: hardness and sulfur, iron and manganese, arsenic, radon and methane
Typical household well depth Depth varies widely across the state. Logs of nearby wells are the best guide
Where to test An ELAP-certified lab. Some county health departments run their own

Who is in charge of a New York well

New York splits well oversight three ways. Here’s who does what:

Agency What it handles
Department of Environmental Conservation (DEC), Water Well Contractor Program Registers water well contractors (the registration number starts with NYRD) under ECL 15-1525 and 6 NYCRR Part 602, requires a preliminary notice before drilling, and receives the well completion report the driller files when the well is finished
Department of Health (NYSDOH) Writes the construction standard every new residential well must meet (10 NYCRR Appendix 5-B) and runs ELAP, the program that certifies labs to test drinking water
County health departments Apply both. In most upstate counties that means a construction permit and an inspection. In some counties it also means a required water test before the well can be used

The state does not test private well water. That part is up to you.

What is required, and what is left to you

New York’s rules cover who builds the well and how. Every new well must have:

  • A registered contractor. Every new well must be built by a DEC-registered contractor and reported.
  • Notice before and a report after. The driller files a preliminary notice with DEC before drilling and sends a well completion report to DEC and to you once the well is done.
  • Disinfection. Appendix 5-B requires the driller to disinfect the well before handing it over.
  • Local rules on top. Some counties put the state’s testing advice into their sanitary code and will not sign off on a new well without a passing sample. Some towns add a building permit for the well and pump.

Beyond that, the state does not require a test at sale. Here’s where it stands:

At a glance

Water test for a new wellNot required statewide

No single statewide rule. The driller must be DEC-registered, file a preliminary notice before drilling, disinfect the finished well under NYSDOH Appendix 5-B, and send a well completion report to DEC and to you when the well is done. NYSDOH says a new well should be tested before use for coliform bacteria, nitrate, nitrite, arsenic, lead, iron, manganese, sodium, hardness, pH and turbidity. Some county health departments require a permit and a passing water test before a new well can be used.

Water test when a home is soldNot required statewide

No statewide requirement. A few counties and towns require a well test or well inspection when a property changes hands, and some lenders ask for a bacteria and nitrate test. Check with the county health department.

What the state recommends

NYSDOH recommends a coliform bacteria test every year, plus a first-time panel of nitrate, nitrite, arsenic, lead, iron, manganese, sodium, sulfate, hardness, pH, alkalinity and turbidity, then periodic re-testing of whatever showed up. Add radon, uranium, methane or PFAS where they are known in your area.

Free or low-cost testingAvailable

No statewide free program. Several county health departments run their own ELAP-certified labs and sell low-cost bacteria and nitrate tests (Erie, Monroe, Suffolk, Nassau, Cattaraugus, Chautauqua, Allegany). Others keep a list of local certified labs.

What the water is like in each part of New York

The geology changes fast in New York, from Long Island’s glacial aquifer to the bedrock of the Adirondacks and the Southern Tier, and so does the water. Find your area below.

Region Typical household well What to expect
Mohawk Valley and the western counties (limestone and dolomite) Drilled into bedrock Hard water and sometimes sulfur. Barium and fluoride turn up in western New York.
Southern Tier (shale) Drilled into bedrock Iron, manganese, methane, sulfate and hydrogen sulfide, and in places radon and uranium.
Central and western glacial valleys Often shallower, in sand and gravel Arsenic where glacial deposits sit on certain bedrock, and nitrate in farm valleys.
Long Island In the sandy glacial aquifer Soft water, but vulnerable to nitrate and to the industrial solvents and PFAS that county labs now screen for.

Depth varies widely across the state, from wells in glacial sand and gravel to deep bedrock wells. Logs of nearby wells are the best guide, and our well record finder links to them.

A few problems cross every region. Road salt has pushed sodium and chloride into shallow wells along busy roads for decades. Adirondack bedrock can carry radon and uranium, nitrate shows up near older septic areas, and PFAS has hot spots such as Hoosick Falls and Newburgh. The lesson is the same everywhere: one broad first test, then a yearly bacteria check, tells you which of these applies to your well.

What to test for

This follows the New York State Department of Health’s private well guidance and its fact sheet for new wells, along with Cornell Cooperative Extension’s testing advice.

Test How often Who needs it
Coliform bacteria Every year, ideally in late spring or early summer Every well
A first-time panel: coliform bacteria, nitrate, nitrite, arsenic, lead, iron, manganese, sodium, chloride, sulfate, hardness, pH, alkalinity and turbidity Once, before you drink from a new well Every new well, and any home you are buying
Whatever showed up on the first test Every 3 to 5 years Every well
Lead and copper With the first test Older homes, and wells with corrosive water (pH under 6.5)
Radon, uranium, radium, barium, fluoride and methane Add to the first test where they are known Southern Tier and Adirondack bedrock, Southern Tier shale and western New York
Sodium, chloride, barium and strontium As a baseline Wells near gas drilling
Nitrate, pesticides, arsenic and coliform Add to the regular check Wells near intensive farming
PFAS and solvents Where they are known in your area Long Island, Hoosick Falls, Newburgh, and wells near industry, landfills or gas stations
Bacteria retest After disinfection or well work, flooding, a land use change nearby, or a change in look, smell or taste Every well

Why bacteria gets top billing: it’s the one test NYSDOH asks for every year, and it shows up more often than people expect. When the USGS sampled 33 public supply and private wells in the upper Susquehanna River basin in 2004 and 2005, total coliform turned up in 6 of them, about 18%. The same study found radon over the proposed 300 picocuries per liter limit in 24 wells and manganese over the 50 microgram per liter guideline in 14. If a result comes back bad, our shock chlorination calculator, arsenic guide, uranium guide and treatment planner walk you through the next step.

ELAP-certified labs, including county labs

You have two ways to get tested in New York:

Option Best for Cost
County health department lab (Erie, Monroe, Suffolk, Nassau, Cattaraugus, Chautauqua and Allegany) The yearly bacteria and nitrate check Sold at cost, the cheapest route
Commercial ELAP lab A full first-time panel, arsenic, lead, radon or PFAS Varies by lab

New York has no statewide free testing program. Counties without their own lab keep a list of local certified labs. Follow the lab’s sampling instructions closely, since lead and bacteria samples can give false results if they aren’t collected properly.

Only a lab accredited by the NYSDOH Environmental Laboratory Approval Program for potable water may report results a health department will accept. The list below comes from the ELAP accreditation database (potable water scope), checked September 29, 2026, and shows each lab’s accredited analytes and whether it is a county lab or a commercial one.

See all 45 certified labs in New York

DEC-registered well contractors

Three things to know before you hire in New York:

  • One registration covers the whole job. A contractor needs a DEC registration to drill, deepen, hydrofracture or decommission a well, or to install or service a pump.
  • Registration is annual. Ask to see the current card before work starts.
  • Keep the paperwork. The driller must send you a copy of the well completion report. It’s the record of your well’s depth, casing and yield.

The profiles below come from the DEC Water Well Contractor Search on September 29, 2026, and show each registrant’s number and the activities DEC lists for them, including out-of-state drillers registered to work in New York.

See all 493 licensed contractors in New York

By county

Well use swings hard from county to county:

  • Under 10% of residents: New York City and Nassau County (under 1%), Monroe (2%), Westchester (5%) and Suffolk (8%) counties
  • About a quarter to a third: Orange (22%), Saratoga (24%), Broome (26%), Rensselaer (32%) and Dutchess (33%) counties
  • Half or more: Schuyler (65%), Schoharie (61%), Columbia (61%), Tioga (58%) and Sullivan (53%) counties

Suffolk has the most well users of any county, about 120,000 people, even though that is only 8% of its residents. Each county page carries its well population, the nearest certified labs and the registered contractors based there.

New York well water questions

Do I need a permit to drill a well in New York?

Not from the state, but from your county health department in most counties, and the driller must be DEC-registered and file a preliminary notice with DEC before drilling. Some towns add a building permit for the well and pump.

Is a water test required when I sell my house?

No statewide test is required. Some counties and towns require one, and some lenders ask for a bacteria and nitrate test.

How do I find the record for my well?

Search the DEC Water Well Information Search or DECinfo Locator by address or town. Completion reports on file show the depth, casing, yield and the driller. Older wells often have no record.

Which lab should I use?

Any lab on the ELAP list for potable water. If your county health department runs a lab, start there for bacteria and nitrate. For a full first-time panel, arsenic, lead, radon or PFAS, use one of the commercial labs listed above.

How often should I test my well in New York?

NYSDOH recommends a bacteria test at least once a year, best in late spring or early summer, and a test for other contaminants every 3 to 5 years. Test a new well before you drink from it, and retest after flooding, well work, or any change in how the water looks, smells or tastes.