Private well guide

Well Water in Washington: Testing, Rules, Labs and Licensed Contractors

About 681,000 people in Washington get their water from a private well, by the U.S. Geological Survey's estimate. Here is what the state requires, where to get it tested, and who is licensed to work on it.

218Licensed contractorschecked against state records
38Certified labsfrom the state certified list
39Counties covered
681,000People on private wells10% of residents (USGS, 2010)

The short version: About 681,000 Washingtonians, 10% of residents, drink from a private well (USGS estimate, 2010). In the most rural counties it is closer to one in two. The state keeps a tight hand on how a well is drilled and who drills it, files a report on every one, and then leaves the water to the owner and the county. Your county will likely want a coliform and nitrate result before it issues a building permit, and after that, testing is up to you.

Washington at a glance
Permit to drill a home well No permit as such. The driller files a notice of intent and fee with Ecology at least 72 hours before drilling
Who can drill it A driller with an Ecology water well operator license
Water test for a new well No statewide test, but most counties want a coliform and nitrate result before they issue a building permit
Water test when a home sells Not required statewide (some lenders ask for one, and a few counties require a test or inspection)
Biggest natural concern Arsenic, found in some Washington wells at levels from 10 ppb up to 33,000 ppb
Typical household well depth Varies widely across the state. Logs of nearby wells are the best guide
Where to test A county health lab or an Ecology-accredited lab that takes public samples

Who is in charge of a Washington well

The Department of Ecology owns the well itself. The water belongs to the health departments. Here’s who does what:

Agency What it handles
Department of Ecology, Well Construction and Licensing Program Licenses water well operators (chapter 173-162 WAC), takes the notice of intent and fee for every well, sets the construction standards in chapter 173-160 WAC and keeps the well reports, which become public in the well report map
Ecology’s Laboratory Accreditation Program Accredits environmental labs, and its lab search marks the labs that accept samples from the public
Department of Health and the county health departments Set the potable water proof a county wants before it issues a building permit, run most of the local labs, and answer the phone when a test comes back bad

Ecology does not test the water. No state office samples your well unless you ask.

What is required, and what is left to you

Washington regulates the drilling closely and the water hardly at all. Every new well needs:

  • A licensed driller. The driller must hold an Ecology water well operator license.
  • A notice of intent. The driller files it with Ecology and pays the fee at least 72 hours before the hole is started.
  • Construction to the standard. Chapter 173-160 WAC sets the rules, including 100 feet from septic drainfields, a surface seal and a well tag.
  • A well report. It goes to Ecology within 30 days and becomes public in the well report map.
  • A check on water rights. A household well pumping under 5,000 gallons a day needs no water right, though since 2018 new domestic wells in some watersheds pay a mitigation fee and face limits.

Your county almost certainly will ask for a coliform and nitrate result before it approves a house on the new well, and some add arsenic. That is usually the only test the well ever gets unless you keep it up. Nothing is required when a home is sold. Here’s where the state stands:

At a glance

Water test for a new wellNot required statewide

No statewide water test from Ecology. What the state requires is a notice of intent and fee filed with Ecology at least 72 hours before drilling, a licensed water well driller, construction to the chapter 173-160 WAC standards (100 ft from septic drainfields, surface seal, a well tag) and a well report filed within 30 days. The test comes in through the county: to get a building permit on a well, most counties ask for proof of potable water, which usually means a coliform bacteria and nitrate test from an accredited lab, and some add arsenic. Check with your county health department before the well is drilled.

Water test when a home is soldNot required statewide

No statewide requirement. The seller disclosure form (Form 17) only asks whether the property is on a well and whether the water has been tested. Some lenders require a water test before closing, and a few counties require a well inspection or water test when a property with a well changes hands.

What the state recommends

The Washington Department of Health recommends testing a private well for coliform bacteria and nitrate every year, retesting nitrate in 6 months if it is 5 mg/L or higher, and testing for arsenic at least twice, once in summer and once in winter. Add hardness, iron, manganese, fluoride, uranium and radon on a first panel, PFAS near military airfields and fire training sites, and test again after flooding, a change in taste, color or smell, or any work on the well.

Free or low-cost testingAvailable

No statewide free testing. A few local programs test for free or at cost: the Whatcom Conservation District tests nitrate in the Sumas-Blaine aquifer, the Lower Yakima Valley groundwater program tests nitrate in that area, and several county health departments and conservation districts run testing days. The Department of Health says free nitrate and coliform testing is available inside set boundaries of the Lower Yakima Valley and western Benton County. Otherwise, county health laboratories run coliform and nitrate tests for a fee, and Ecology's lab list marks which labs accept samples from the public.

What the water is like in each part of Washington

The Cascades split the state in two, and the water changes on each side. Find yours below.

Region Typical household well What to expect
Puget Sound lowland and western Washington (glacial sand and gravel) Varies widely; see nearby well logs Iron and manganese staining, arsenic in the deeper glacial layers around Puget Sound (Whatcom, Snohomish and Pierce counties), and bacteria in the shallow and dug wells that are still common in the older counties.
Columbia Plateau, including the Yakima and Walla Walla valleys (basalt) Varies widely; see nearby well logs Hard, alkaline water, sometimes with fluoride and sodium from depth, and arsenic in places. The farm valleys carry nitrate: the Lower Yakima Valley, the Columbia Basin and the Spokane-Rathdrum valley.
Cascade and Okanogan foothills and the northeast (fractured rock) Varies widely; see nearby well logs Low yields. The granite country of Okanogan, Stevens and Spokane counties adds uranium and radon.

Two spots need their own mention. Island and shoreline wells in San Juan, Island, Kitsap and Jefferson counties can turn salty as they are pumped. And the Lower Yakima Valley and the Sumas-Blaine aquifer in Whatcom County are the two areas where the state has had to step in over nitrate.

Depth varies widely across the state, even between neighbors. Logs of nearby wells are the best guide, and our well record lookup shows you where to find them. A broad first test tells you which of these problems is yours.

What to test for

This follows the Washington State Department of Health’s private well advice.

Test How often Who needs it
Coliform bacteria Every year Every well
Nitrate Every year, and again in 6 months if the result is 5 mg/L or higher Every well, and the farm valleys of the Yakima, Columbia Basin, Spokane-Rathdrum and Sumas-Blaine areas most of all
Arsenic At least twice while you own the well, once in summer and once in winter Every well, especially around Puget Sound and in Whatcom, Snohomish and Pierce counties
Hardness, iron, manganese, fluoride, uranium and radon With the first panel Every well. Uranium and radon matter most in Okanogan, Stevens and Spokane counties
PFAS With the first panel Wells near military airfields and fire training sites
Coliform and nitrate again When someone in the home is pregnant, nursing or has an unexplained illness Any household in that spot
Full retest After flooding, any work on the well, or a change in taste, color or smell Every well

Why nitrate and arsenic get top billing: in a 2017 USGS study of 156 wells in the Lower Yakima Valley, more than 20% of samples from household wells were over the 10 mg/L nitrate limit, and 26% of the wells topped it at least once. The Department of Health says arsenic levels from 10 ppb to 33,000 ppb have been found in some Washington wells. You can’t taste or smell either one. If a result comes back high, our arsenic guide, uranium guide, shock chlorination calculator and treatment planner walk you through the next step.

Ecology-accredited labs and county health labs

You have three ways to get tested in Washington:

Option Best for Cost
County health department lab The yearly coliform test, and usually nitrate as well Varies by county. Ask your county health department
Ecology-accredited commercial lab Arsenic, metals, uranium, PFAS and the wider panel Labs usually charge $20 to $35 for an arsenic test
Local free programs Nitrate in the areas with known problems Free inside the program boundaries

Washington has no statewide free testing, but a few local programs fill the gap. The Whatcom Conservation District tests nitrate in the Sumas-Blaine aquifer. The Lower Yakima Valley groundwater program tests nitrate in that area, and the Department of Health says free nitrate and coliform testing is available inside set boundaries of the Lower Yakima Valley and western Benton County. Several county health departments and conservation districts also run testing days.

Washington accredits environmental labs through Ecology’s Laboratory Accreditation Program. Every lab below holds current drinking water accreditation and takes public samples, and most of the commercial labs will mail bottles anywhere in the state.

See all 38 certified labs in Washington

Licensed water well drillers

Three things to know before you hire in Washington:

  • Washington licenses the driller, not the company. Look the driller up on Ecology’s licensed driller search before you sign.
  • Pump work is not licensed by the state. Most drilling companies do it, but pump-only companies are not on this list.
  • Talk to your county before the well is drilled. The driller handles the Ecology paperwork, but the county decides what water test it needs before it issues a building permit.

Every profile below is built from an active Ecology water well operator license, grouped under the drilling company Ecology lists for the licensee, with each licensed driller named. Because Ecology publishes every well report with the driller’s license number, the profiles also show how many water wells the company has reported since 2016 and in which counties, which is the most reliable guide to who is actually drilling near you.

See all 218 licensed contractors in Washington

By county

Well use swings hard from county to county:

  • Fewest wells around the big cities. About 2% of King County residents drink from a private well, and about 5% to 6% in Asotin, Snohomish and Pierce counties.
  • About one in six in the middle. Thurston County is at about 17%, and Clallam, Chelan and Walla Walla counties 16%.
  • Close to half in the top counties. About 48% of Pend Oreille County residents, 47% in Ferry County, 45% in Stevens County and 40% in Okanogan County.

Each county page carries its well population, the nearest accredited labs and the licensed drillers based there.

Washington well water questions

Do I need a permit to drill a well in Washington?

Not a permit as such, but three things that work like one. The driller files a notice of intent with Ecology before drilling. A household well under 5,000 gallons a day is exempt from a water right, with mitigation fees and limits in some watersheds since 2018. And your county needs proof of adequate potable water before it issues a building permit. Your licensed driller handles the Ecology side.

Is a water test required when I sell my house in Washington?

No, not statewide. The seller disclosure form (Form 17) only asks whether the property is on a well and whether the water has been tested. Some lenders require a water test before closing, and a few counties require a well inspection or test at transfer, so ask your county health department.

How often should I test my well in Washington?

Every year for coliform bacteria and nitrate, as the Department of Health recommends, and arsenic at least twice while you own the well, once in summer and once in winter. If nitrate comes back at 5 mg/L or higher, test again in six months. Retest after flooding, well work or a change in taste, color or smell.

How deep are wells in Washington?

Depth varies widely across the state, because it depends on the ground under your property. Logs of nearby wells are the best guide. Use our well record lookup to find them in Ecology’s well report map.

How do I find the record for my well?

Use Ecology’s well report map. Search by address or parcel and open the well report, which shows the depth, casing, seal, static water level and yield. Most wells drilled in recent decades have one.

Which lab should I use?

Any lab on Ecology’s accredited list that accepts public samples. Use a county health lab for the yearly coliform and nitrate check and a commercial lab for arsenic, metals, uranium or PFAS.